HOME ABOUT US GALLERY PRO-CORE CONTACT BUILDING TIPS
Building 101
Glossary of Terms
A/C: An abbreviation for air conditioner or air conditioning.
A/C Condenser: The condenser is the outside fan unit of the Air Conditioning
system. It removes the heat from the Freon gas and "turns" the gas back into a
liquid and pumps the liquid back to the coil in the furnace.
A/C Disconnect: The main electrical ON-OFF switch near the A/C Condenser.
Acrylic Knockdown (AKD): Finish applied to a concrete floor surface. Typically
applied on porch floors and decking surrounding swimming pools. The concrete
deck receives a textured finish. It then receives an acrylic elastic type paint
or coating applied over the textured finish. It can be easily recoated or
painted later which makes it appear new again. Any exterior floor area in
Florida should be hosed down weekly to keep mildew at bay.
Aerator: The round screened screw-on tip of a sink spout. It mixes water and air
for a smooth flow.
Air Conditioned Living Area: The square footage of the area that is air
conditioned in a home. Areas such as garage, porches, non air conditioned attic
storage areas, etc. are not included in this measurement. When cost per square
foot is considered the cost of the home is typically divided by the square
footage of Air Conditioned Living Area. Large amounts of non air conditioned
area canhave a huge impact on the cost per square foot of a home.
Allowances: In the specifications for the construction of a home typically
numerous items are called allowances. They are typically decorator items such as
cabinets, tile, wallpaper, carpet, landscaping, etc. The Builder will base the
price of the home including allowances for the items agreed to as allowance
items. Depending upon the choices the Buyer makes they will receive a credit if
their choice is less than the allowance, none if the same as the allowance, or
they will be charged the additional amount if their choice cost more than the
allowance for that particular item. This is an area that allows many
unscrupulous Builders to offer a below market price for a home by reducing the
allowances. The Buyers receive many unpleasant surprises when Builders do this
throughout the process. It is not at all unusual to find out that the Builder
with the higher bid has in fact the lowest cost in the end due to this practice.
Protect yourself by doing some research on what you desire for the allowance
items vs. the allowance offered.
Amortization: A payment plan by which a loan is reduced through monthly payments
of principal and interest.
Annual Percentage Rate (APR): Annual cost of credit over the life of a loan,
including interest, service charges, points, loan fees, mortgage insurance, and
other items.
Architectural Ceilings: Known as tray ceilings or other specially designed
ceilings. They are typically designed by the Interior Architectural Designer and
not the Architect or Designer of the home.
Astragal: A molding, attached to one of a pair of swinging double doors, against
which the other door strikes.
Attic access: An opening that is placed in the drywalled ceiling of a home
providing access to the attic
Automated lighting control system: A professionally installed system that
controls lights in multiple rooms without use of manual switches.
Backsplashes: Wall area between the cabinet countertop and the upper cabinets.
This area can have tile, granite, wallpaper, or painted an accent color.
Balusters: Vertical members in a railing used between a top rail and bottom rail
or the stair treads. Balusters are sometimes referred to as 'pickets' or
'spindles'.
Balustrade: The rail, posts and vertical balusters along the edge of a stairway
or elevated walkway are known as the Balustrade.
Banding: Typically refers to exterior veneer of the home. Banding is the trim
installed around windows, doors, and other exterior architectural features of
the home. It can be made out of stucco, wood, or stone.
Bath Accessories: Includes the toilet tissue holder and towel bars. They can be
metal or ceramic.
Bi-fold door: Doors that are hinged in the middle for opening in a smaller area
than standard swing doors. Often used for closet doors.
Bi-pass doors: Doors that slide by each other and commonly used as closet doors.
Bottom chord: The lower or bottom horizontal member of a truss.
Breaker panel: The electrical box that distributes electric power entering the
home to each branch circuit (each plug and switch) and composed of circuit
breakers.
Builder's Risk Insurance: Insurance coverage on a construction project during
construction, including extended coverage that may be added for the contract for
the customer's protections.
Building codes: Local and state ordinances governing the manner in which a home
may be constructed or modified.
Built INS: Can be anywhere in the home. The Built Ins are typically designed by
the Interior Architectural Designer. They are normally built into some type of
niche specially prepared for the Built in. They are highly personalized and not
inexpensive. Normally, the built-ins are finished wood and include TV
entertainment centers, Bookcases, Desk, Storage Chest, and much more.
Bull nose (drywall): Rounded drywall corners.
Café Grille Hood: Installed on the rear porch over the outdoor grille. They
should include a venting system to remove all smoke and odor to the outside
through the roof or side wall of the home.
Cantilever: An overhang where one floor extends beyond and over a foundation
wall. For example at a fireplace location or bay window cantilever.
Casement: A window that one side of the window sash cranks out.
Casing: The casing is the wood trim molding installed around a door or window
opening.
Cast Stone: Man made material to resemble coral stone or some other type of
natural stone. Cast Stone is very expensive. Many times the same look can be
accomplished through our stucco artists at a fraction of the cost.
Cement: The gray powder that is the "glue" in concrete. Portland cement. Also,
any adhesive.
Ceramic tile: A man-made or machine-made clay tile used to finish a floor or
wall. Generally used in bathtub and shower enclosures and on counter tops.
Certificate of Occupancy: Issued by the County Building Department once the home
has passed all of the required inspections by the County building department.
This certificate is issued by the local municipality and is required before
anyone can occupy and live within the home. It is issued only after the local
municipality has made all inspections and all monies and fees have been paid.
CFM (cubic feet per minute): A rating that expresses the amount of air a blower
or fan can move. The volume of air (measured in cubic feet) that can pass
through an opening in one minute.
Chair rail: Interior trim material installed about 3-4 feet up the wall,
horizontally.
Circuit Breaker: A device which looks like a switch and is usually located
inside the electrical breaker panel or circuit breaker box. It is designed to
(1) shut of the power to portions or all of the house and (2) to limit the
amount of power flowing through a circuit (measured in amperes). 110 volt
household circuits require a fuse or circuit breaker with a rating of 15 or a
maximum of 20 amps. 220 volt circuits may be designed for higher amperage loads
e.g. a hot water heater may be designed for a 30 amp load and would therefore
need a 30 amp fuse or breaker.
Circuit: The path of electrical flow from a power source through an outlet and
back to ground.
CO: An abbreviation for "Certificate of Occupancy".
Cold air return: The ductwork (and related grills) that carries room air back to
the furnace for re-heating.
Combustion air: The duct work installed to bring fresh, outside air to the
furnace and/or hot water heater. Normally 2 separate supplies of air are brought
in: One high and One low.
Compressor: A mechanical device that pressurizes a gas in order to turn it into
a liquid, thereby allowing heat to be removed or added. A compressor is the main
component of conventional heat pumps and air conditioners. In an air
conditioning system, the compressor normally sits outside and has a large fan
(to remove heat).
Concrete block: A hollow concrete 'brick' often 8" x 8" x 16" in size.
Concrete: The mixture of Portland cement, sand, gravel, and water. Used to make
garage and basement floors, sidewalks, patios, foundation walls, etc. It is
commonly reinforced with steel rods (rebar) or wire screening (mesh).
Condensate line: The copper pipe that runs from the outside air conditioning
condenser to the inside furnace (where the a/c coil is located).
Condensation: Beads or drops of water (and frequently frost in extremely cold
weather) that accumulate on the inside of the exterior covering of a building.
Use of louvers or attic ventilators will reduce moisture condensation in attics.
A vapor barrier under the gypsum lath or dry wall on exposed walls will reduce
condensation.
Condensing unit: The outdoor component of a cooling system. It includes a
compressor and condensing coil designed to give off heat.
Conditions, Covenants, and Restrictions (CC and R's): The standards that define
how a property may be used and the protections the developer makes for the
benefit of all owners in a subdivision.
Construction Agreement: The contractual agreement between the Buyers and the
Builder. This agreement spells out the rights, obligations, and duties between
both parties.
Construction Specifications: Attached to the Construction Agreement. The
specifications cannot be too long. Ours are typically 100 pages or more
detailing everything we can think of that has been included with the home as
well as anything that is not. This is a very important document. If it is not a
substantial size document be very careful.
Control joint: Tooled, straight grooves made on concrete floors to "control"
where the concrete should crack
Convection: Currents created by heating air, which then rises and pulls cooler
air behind it. Also see radiation.
Cooling load: The amount of cooling required keeping a building at a specified
temperature during the summer, usually 78° F, regardless of outside temperature.
Corbel: The triangular, decorative and supporting member that holds a mantel or
horizontal shelf.
Corner bead: A strip of formed sheet metal placed on outside corners of drywall
before applying drywall 'mud'.
Cornice: Overhang of a pitched roof, usually consisting of a fascia board, a
soffit and appropriate trim moldings.
Course: A row of shingles or roll roofing running the length of the roof.
Parallel layers of building materials such as bricks, or siding laid up
horizontally.
Deco Drain: Normally found at the intersection of the concrete rear porch and
the concrete pool deck. The drain has a perforated top where the water drains
into a PVC trough and is then directed to the yard of the home. We use a larger
than standard Deco Drain to be sure that no future problems will occur.
Dedicated circuit: An electrical circuit that serves only one appliance (ie,
dishwasher) or a series of electric heaters or smoke detectors.
Disconnect: A large (generally 20 Amp) electrical ON-OFF switch.
Distributed audio system: A professionally installed system that allows
occupants to play and control audio from a central source in at least three
rooms in the home The system should include at a minimum a distribution
amplifier, room controls and in-wall, on-wall or in-ceiling speakers.
Doorjamb, interior: The surrounding case into which and out of which a door
closes and opens. It consists of two upright pieces, called side jambs, and a
horizontal head jamb. These 3 jambs have the "door stop" installed on them.
Dormer: An opening in a sloping roof, the framing of which projects out to form
a vertical wall suitable for windows or other openings.
Double Cylinder Deadbolt: This is a deadbolt lock on a door. Double cylinder
means that a key must be used on both sides of the lock. A single cylinder means
that a key must be used on one side of the door while a lever of some other type
is used to unlock the door on the opposite side.
Double glass: Window or door in which two panes of glass are used with a sealed
air space between. Also known as Insulating Glass.
Double hung: A window that both the upper and lower window sashes move up and
down.
Draw: The amount of progress billings on a contract that is currently available
to a contractor under a contract with a fixed payment schedule.
Driveway approach: Driveway area between the street and the sidewalk at the
front of the property. This area must be concrete as opposed to brick pavers
since it must connect with the street.
Drop in Sink: Sink that is surface mounted on a counter top. The rim of the sink
is visible. A sink that the rim is not visible is called an under mount sink.
Dry in: To install the black roofing felt (tar paper) on the roof.
Ducts: The heating system. Usually round or rectangular metal pipes installed
for distributing warm (or cold) air from the furnace to rooms in the home. Also
a tunnel made of galvanized metal or rigid fiberglass, which carries air from
the heater or ventilation opening to the rooms in a building.
Dura Rock: Reinforced concrete sheets installed on the wall or a wood floor
prior to the installation of tile. The Dura Rock will not rot or absorb water
while green board or water resistant drywall will. This is a must for all wall
tile and tile installed on wood floors.
Easement: A formal contract which allows a party to use another party's property
for a specific purpose. e.g. a sewer easement might allow one party to run a
sewer line through a neighbor’s property.
Eaves: The horizontal exterior roof overhang.
Egress: A means of exiting the home. An egress window is required in every
bedroom and basement. Normally a 4' X 4' window is the minimum size required
Electrical Rough: Work performed by the Electrical Contractor after the plumber
and heating contractor are complete with their phase of work. Normally all
electrical wires and outlet, switch, and fixture boxes are installed (before
insulation).
Electrical Trim: Work performed by the electrical contractor when the house is
nearing completion. The electrician installs all plugs, switches, light
fixtures, smoke detectors, appliance "pig tails", and bath ventilation fans,
wires the furnace, and "makes up" the electric house panel. The electrician does
all work necessary to get the home ready for and to pass the municipal
electrical final inspection
Elevation: Drawing depicting the final look of an element such as each side of
the home.
Evaporator coil: The part of a cooling system that absorbs heat from air in your
home. Also see condensing unit.
Expansion joint: Fibrous material (@1/2" thick) installed in and around a
concrete slab to permit it to move up and down (seasonally) along the non-moving
foundation wall.
Exterior Rock Salt Accent Painting: This treatment can be applied to stucco
banding, columns, window sills, etc. that has been pitted with rock salt to
resemble cast stone. It is a 2-3 stage treatment. First, the material is painted
with the color desired for the pitted area of the surface. It is then repainted
with the color desired for the main area of the surface. This treatment makes
the pitted areas stand out and really finishes the cast stone look for a
fraction of the cost of cast stone. Sometimes, our clients have the banding and
other faux stone trim faux painted for an even nicer, more authentic look.
Fascia: The flat, vertical surface immediately below the edge of a roof. It is
the surface a gutter would be attached to. The term fascia can also be used to
describe other flat vertical surfaces in a home.
Faux Painting: Paint applied by an artist to a surface in a manner to match a
certain pattern and color desired. Normally requires a base coat of paint with
numerous other coats of other color paint to achieve the desired look. Faux
painting is used on walls and many other surfaces. Almost any faux look can be
accomplished.
Felt- Tar paper: Installed under the roof shingles. Normally 15 lb. or 30 lb.
Flashing: Sheet metal or other material used in roof and wall construction to
protect a building from water seepage.
Flatwork: Common word for concrete floors, driveways, basements, and sidewalks.
Flue: Large pipe through which fumes escape from a gas water heater, furnace, or
fireplace. Normally these flue pipes are double walled, galvanized sheet metal
pipe and sometimes referred to as a "B Vent". Fireplace flue pipes are normally
triple walled. In addition, nothing combustible shall be within one inch from
the flue pipe.
Foam Insulation: Foam insulation is injected into the exterior concrete block
wall cavities not filled with concrete. Foam insulation not only offers a great
insulation value, but also provides excellent sound insulation. More importantly
though, it fills every cavity and void in the exterior walls eliminating places
where bugs and other pest can reside and enter the home.
Footer: The concrete reinforced supporting base or groundwork of the home.
Foundation Wall: The concrete block walls built on top of the footer to the
height of the slab. The area inside the foundation walls is filled with
compacted fill.
Framer: The carpenter contractor that installs the lumber and erects the frame,
flooring system, interior walls, backing, trusses, rafters, decking, installs
all beams, stairs, soffits and all work related to the wood structure of the
home. The framer builds the home according to the blueprints and must comply
with local building codes and regulations.
Framing: Lumber used for the structural members of a building, such as studs,
joists, and rafters.
French Drains: Installed below the surface of the ground to aid movement of
ground water outside the home. A trench is dug in which a perforated PVC pipe is
installed. The pipe is embedded in gravel and the pipe is then directed to a
positive drain source. The pipe, if properly sloped, will do an excellent job
draining wet areas. French drains are also known as under drains.
Frieze Bands: A plain or decorated vertical band installed below the exterior
soffit and the exterior vertical veneer of the home for decorative purposes. The
band is typically thicker than the adjacent wall surface and of another texture
so that the band will be prominent in appearance. This term could also describe
a band treatment inside the home just below the ceiling.
Glazing: The process of installing glass, which commonly is secured with
glazier's points and glazing compound.
GPM: This is a measurement that describes the number of gallons that can flow
through a particular pipe or other item per minute.
Grade: Ground level or the elevation at any given point. Also the work of
leveling dirt. Also the designated quality of a manufactured piece of wood.
Ground fault: Ground Fault Circuit Interrupter (GFCI, GFI) - an ultra sensitive
plug designed to shut off all electric current. Used in bathrooms, kitchens,
exterior waterproof outlets, garage outlets, and "wet areas". Has a small reset
button on the plug.
Ground iron: The plumbing drain and waste lines that are installed beneath the
basement floor. Cast iron was once used, but black plastic pipe (ABS) is now
widely used.
Ground: Refers to electricity's habit of seeking the shortest route to earth.
Neutral wires carry it there in all circuits. An additional grounding wire or
the sheathing of the metal-clad cable or conduit—protects against shock if the
neutral leg is interrupted.
Groundwater: Water from an aquifer or subsurface water source.
Grout: A wet mixture of cement, sand and water that flows into masonry or
ceramic crevices to seal the cracks between the different pieces. Mortar made of
such consistency (by adding water) that it will flow into the joints and
cavities of the masonry work and fill them solid.
Gypsum Board: Gypsum is used to create drywall. Drywall is the interior wall and
ceiling surface of your home. It comes in 4’x12’ sheets that are taped and
finished.
Hardware: All of the "metal" fittings that go into the home when it is near
completion. For example, door knobs, towel bars, handrail brackets, closet rods,
house numbers, door closers, etc. The Interior Trim Carpenter installs the
"hardware".
Heat Recovery Units: Use waste heat from your air conditioning system to heat
domestic hot water.
Heat Rough: Work performed by the Heating Contractor after the stairs and
interior walls are built. This includes installing all duct work and flue pipes.
Sometimes, the furnace and fireplaces are installed at this stage of
construction.
Heat Trim: Work done by the Heating Contractor to get the home ready for the
municipal Final Heat Inspection. This includes venting the hot water heater,
installing all vent grills, registers, air conditioning services, turning on the
furnace, installing thermostats, venting ranges and hoods, and all other heat
related work.
Hip: A roof with four sloping sides. The external angle formed by the meeting of
two sloping sides of a roof.
Hip roof: A roof that rises by inclined planes from all four sides of a
building.
Home automation system: A professionally installed system that integrates the
control of security, HVAC or lighting systems to enhance safety, comfort and
convenience.
Home run (electrical): The electrical cable that carries power from the main
circuit breaker panel to the first electrical box, plugs, or switch in the
circuit.
Home theater system: A professionally installed audio/video system designed to
re-create cinema-like experiences in the home, including at least a five-speaker
surround-sound system (at least installed or mounted on the wall or ceiling) and
a video display measuring 40 inches or more.
Hose Bib: Exterior garden hose outlet.
HVAC: The heating, ventilation, and air conditioning system for your home.
Interior Architectural Detailing: As important or possibly more so that the
architectural plans for your home. They include the plans for all of the special
ceilings, niches, special trim, built ins, decorative tile details, and more for
your home. They are typically prepared by the Interior Designer and Architect.
Irrigation: Exterior sprinkler system for the yard.
Jamb: The side and head lining of a doorway, window, or other opening. Includes
studs as well as the frame and trim.
Joist hanger: A metal "U" shaped item used to support the end of a floor joist
and attached with
Joist: Wooden 2 X 8's, 10's, or 12's that run parallel to one another and
support a floor or ceiling, and supported in turn by larger beams, girders, or
bearing walls.
Keyless: A plastic or porcelain light fixture that operates by a pull string.
Generally found in the basement, crawl space, and attic areas.
Knockdown: Splatter texture applied to a surface that is then troweled to
achieve a particular finish. Normally used to describe finish on drywall
interior walls and ceilings, porch and pool deck floor finishes, as well as a
particular type of exterior wall stucco finish.
Laminate: Formica or other brands surface glued to a wood substrate typically
for countertops.
Light Lift: Typically found where chandeliers are installed in high ceiling
areas. The light lift is electrically operated and raises or lowers the light
fixture for cleaning and maintenance.
Loan in Process Account: When the construction loan closes prior to start of
construction the lender creates an account called the loan in process account or
LIP. The total amount placed in the LIP is the agreed purchase price less any
deposits or prepayments paid. The Builder is then paid from this account as
construction progresses in percentage amounts according to the draw schedule
provided by the lender.
Male: Any part, such as a bolt, designed to fit into another (female) part.
External threads are male.
Masonry: Stone, brick, concrete, hollow-tile, concrete block, or other similar
building units or materials. Normally bonded together with mortar to form a
wall.
Mastic: A pasty material used as a cement (as for setting tile) or a protective
coating (as for
Medallions: Normally adhered to a wall or ceiling. They can be plaster, stone,
precast stone, etc. They are typically decorative in nature.
Millwork: Generally all building materials made of finished wood and
manufactured in millwork plants. Includes all doors, window and door frames,
blinds, mantels, panel work, stairway components (balusters, rail, etc.),
moldings, and interior trim. Does not include flooring, ceiling, or siding.
Miter joint: The joint of two pieces at an angle that bisects the joining angle.
For example, the miter joint at the side and head casing at a door opening is
made at a 45° angle.
Molding: A wood strip having an engraved, decorative surface.
Monitored security system: A professionally installed system designed to detect
intrusion or other hazard, including sensors, an alarm-sounding device and
communication device that reports conditions to an alarm monitoring service.
Mortar: A mixture of cement (or lime) with sand and water used in masonry work.
Mortgagee: The lender who makes the mortgage loan.
Motor Court: Driveway area in front of garage.
Mullion: A vertical divider in the frame between windows, doors, or other
openings.
Muntins: Are typically decorative in nature. Muntins can be a strip of wood or
metal separating and holding panes of glass in a window. Today, they are
typically installed for decorative purposes only since normally one pane of
glass is used for the entire window opening. Today, they are veneered on both
sides of a piece of window glass to duplicate the type of window look shown on
the plans of the home.
Newel post: the large starting post to which the ends of a stair guard railing
or balustrade is fastened.
Nonbearing wall: A wall supporting no load other than its own weight.
Nosing: The projecting edge of a molding or drip or the front edge of a stair
tread.
Pitch: The incline slope of a roof or the ratio of the total rise to the total
width of a house, i.e., a 6-foot rise and 24-foot width is a one-fourth pitch
roof. Roof slope is expressed in the inches of rise, per foot of horizontal run.
Plot plan: An overhead view plan that shows the location of the home on the lot.
Includes all easements, property lines, set backs, and legal descriptions of the
home. Provided by the surveyor.
Programmable Thermostats: Allow the homeowner to program times and temperature
for automatic operation, saving 30% during a typical setback period.
Radiant Barrier: Aluminum foil installed over the air conditioned living area of
the home between the interior ceiling and the roof of the home. It is typically
stapled to the undersides of the sloped roof trusses. Each piece is taped and
sealed. Our trade’s people advise us that this lowers the temperature in the
middle of the summer in attics 30 to 40 degrees. This should have a large impact
on utility cost.
Rebar: Steel reinforcing rods installed in concrete. Objective is to hold the
concrete together.
Receptacle: An electrical outlet. A typical household will have many 120 volt
receptacles for plugging in lams and appliances and 240 volt receptacles for the
range, clothes dryer, air conditioners, etc.
Recessed Box Washer Connection: Installed inside the wall in the laundry where
the clothes washer will be located. Inside this box are the hot and cold water
supplies as well as the drain for the washer.
Recessed lights: Ceiling lights installed in the ceiling of the home by the
electrician.
Redline red lined prints: Blueprints that reflect changes and that are marked
with red pencil.
Retaining wall: A structure that holds back a slope and prevents erosion.
Retaining Walls: When a yard slopes more than normal a retaining wall may be
required. The retaining wall is built from concrete, block, etc. Sometimes they
are required around swimming pools.
Returns: The conditioned air is distributed throughout the home using a system
of rigid and flexible duct, collectively referred to as ductwork. Ductwork is a
circulatory system that uses supplies to feed air into a room and returns to
complete the circuit back to the air handler. Adequate and properly placed
returns will keep closed rooms from becoming pressurized which limit the
entrance of supply air into the room.
Rough opening: The horizontal and vertical measurement of a window or door
opening before drywall or siding is installed.
Roughing-in: The initial stage of a plumbing, electrical, heating, carpentry,
and/or other project, when all components that won't be seen after the second
finishing phase are assembled. See also Heat Rough, Plumbing Rough, and
Electrical Rough.
SEER: Universal energy rating for heat pumps. The higher the number the better.
Sentricon: Termite treatment developed by DuPont. It is a termite baiting system
with baiting stations placed every so many feet around the perimeter of the
home. The baiting systems are continuously monitored for any sign of termite
activity. Should activity occur at any baiting station then that area is heavily
treated for termites. The objective is to stop termites before they reach the
home.
Service entrance panel: Main power cabinet where electricity enters a home
wiring system.
Service equipment: Main control gear at the service entrance, such as circuit
breakers, switches, and fuses.
Service lateral: Underground power supply line.
Sheathing: A layer of plywood or similar type material applied to the studs and
joists of a building to strengthen it and serve as a foundation for a
weatherproof exterior finish.
Single Cylinder Deadbolt: This is a deadbolt lock on a door. Double cylinder
means that a key must be used on both sides of the lock. A single cylinder means
that a key must be used on one side of the door while a lever of some other type
is used to unlock the door on the opposite side.
Single Hung: Refers to a type of window where the bottom window sash goes up and
down. The upper sash remains fixed.
Skimmer: Not the Builder! Typically refers to the pool. It is an inlet where the
pool water is sucked from the pool water surface by the pool pump through the
filtration equipment and returned to the pool as fresh filtered water.
Slide Bolt: Normally found where double doors are used. A slide bolt is
installed at the top and bottom of one of the doors to allow the doors to lock.
The door with the slide bolt remains fixed unless the slide bolts are opened. It
can then be opened or closed.
Soffit: The underside of a structural component, such as a beam, arch,
staircase, or cornice. The term is typically used to refer to the flat
horizontal area between the edge of the roof and the exterior veneer of the
home.
Soil Report: The Soil Engineer takes core samples at various locations on the
home site 7-10 feet deep. He then analyzes the samples for structural capacity
of the soil. His report details those findings and offers his suggestions on how
to deal with any problem soils.
Solarium: A solarium is a room enclosed largely with glass and affording
exposure to the sun. The term solarium as used by a Builder typically refers to
the wall built surrounding this room. The wall allows the room to remain open to
the sun, but affords privacy at the same time.
Span: The clear distance that a framing member carries a load without support
between structural supports. The horizontal distance from eaves to eaves.
Street Tree: Most communities today require the Builder to install an oak tree
of a certain size or other similar agreed tree species every 50 feet or other
length of street frontage.
Structured Wiring System: The future of all homes! A central box is installed
inside the home in an easily accessible location. All TV and telephone outlets
are then wired directly to each outlet from this box. The telephone, cable
television, satellite, fiber optic, and other lines coming into the home from
the outside are wired directly to this box. The computers can be networked
through this box, distributed audio and video systems can be installed, as well
as home automation and lighting controls can be installed in this system. Dave
Brewer was ranked #3 in the country last year among Custom Home Builders in the
use of technology in our homes.
Supplies: The conditioned air is distributed throughout the home using a system
of rigid and flexible duct, collectively referred to as ductwork. Ductwork is a
circulatory system that uses supplies to feed air into a room and returns to
complete the circuit back to the air handler. Adequate and properly placed
returns will keep closed rooms from becoming pressurized which limit the
entrance of supply air into the room.
Surface-mount: Mounted on the surface of something as opposed to under mount
which would be a recessed mounting.
Threshold: A piece of aluminum or wood placed beneath a door; a doorsill. It
typically has vinyl or rubber weather stripping installed to not only save
energy cost, but also to prevent pests from entering the home.
Tile Decos: Describes the decorative treatments installed in tile surfaces.
Decos may be the same tile turned or sized differently. It may also be another
tile material installed for decorative purposes.
Top chord: The upper or top member of a truss.
Transom: A window or opening installed above a door or window.
Trap: A plumbing fitting that holds water to prevent air, gas, and vermin from
backing up into a fixture.
Trusses: Engineered wood roof system.
Tubes-In-The-Wall: Perforated tubes installed in every exterior and interior
wall in the home. The tubes all lead to an injection port on the outside of the
home. Periodically, pressurized fumigant is sent through the port into the tubes
and disbursed in the wall cavities of the home. It is an excellent method for
pest control.
Tubes-Under-The-Slab: Perforated tubes are installed under the slab under the
visquene vapor barrier prior to the slab being poured. All tubes lead to an
injection port. Pressurized termite fumigant is sent through the port into the
tubes and disbursed below the slab. It is an excellent method for pest control.
Tyvek or similar material: Applied to the exterior wood plywood sheathing on all
frame wall areas of the home. It is a plastic type material that does an
excellent job of preventing moisture entering the home through the exterior
walls.
Under drains: Installed below the surface of the ground to aid movement of
ground water outside the home. A trench is dug in which a perforated PVC pipe is
installed. The pipe is embedded in gravel and the pipe is then directed to a
positive drain source. The pipe if properly sloped will do an excellent job
draining wet areas. Under drains are also known as French drains.
Under-layment: Material installed between two surfaces. An example is a pad
under-layment is installed between the concrete slab and the carpet. Dave Brewer
is the only Builder we know that installs a second layer of plywood type wood
under-layment over the top of all plywood floors on two story homes. The second
layer reduces noise transmission and creates a stiffer floor that all Custom
home Buyers deserve in their home.
Under-mount: Refers to a sink installed below a counter top making the sink and
the top appear to be one piece.
Valley: The "V" shaped area of a roof where two sloping roofs meet. Water drains
off the roof at the valleys.
Vapor Barrier: Visquene installed to prevent moisture from passing between two
locations. A vapor barrier is installed on top of the foundation fill prior to
pouring the slab. This prevents condensation entering the floor of the home from
the ground below.
Water Closet: Toilet or commode.
Wood Inserts: Wood Inserts in the specifications refers to a decorative design
created out of wood installed inside some type of niche in the home.
Zoning: Zoning the Air Conditioning System allows a home to be separated into
multiple zones. Each zone has individualized control with its own thermostat.
Also: A governmental process and specification which limits the use of a
property e.g. single family use, high rise residential use, industrial use, etc.
Zoning laws may limit where you can locate a structure. Also see building codes